HOMAG AND LIGMATECH KAL310/8/A20/S2 Edge bander with Boomerang

Top lot

Lot br. 1

1/42

Licitiranje ovog lota je završeno

Da li vas interesira ovaj artikl?
Uputite zahtjev za neobvezujuću ponudu.

Pojedinosti ponude

Naziv

HOMAG AND LIGMATECH KAL310/8/A20/S2 Edge bander with Boomerang

Broj artikla

926783

Proizvođač

HOMAG AND LIGMATECH

Tip

KAL310/8/A20/S2

Godina proizvodnje

2003

Artikl dostupan od

immediately

Stanje artikla

Lokacija

Švedska, 696 32 Askersund

Prikaži na karti
Svi artikli na ovoj lokaciji

Troškovi i povlastice

Troškovi demontiranja i ukrcaja (obvezujuće): 100,00 €
Troškovi prijevoza: nisu uključeni
Uvjeti dostave: FCA Askersund, ukrcano na kamion
Uvjeti plaćanja: 100% plaćanje prije preuzimanja

Tehničke pojedinosti

upravljanje: NC21
približno određivanje mjere (d x š x v)(: 13.600 x 2.450 x 2.600 mm
Približna masa: 8.000 kg

Opis artikla

Edgebander with return system

Equipped with the following units:

10-place moulding magazine
Cutter unit
Fine milling unit
Radius milling unit
Corner rounding unit
Profile milling unit
Scraper unit
Polishing unit

Technical data:

Homatic electronic control Feed unit: NC21
Operation Windows
Feed rate: 18 m/min
Working height of the machine: 950 mm
Workpiece width: min.55 mm, max 100 mm
Workpiece overhang: 30 mm
Workpiece thickness: 12 - 60 mm
Edge material thickness (mouldings): 0.4 - 20 mm
Max. cross section: 900 mm²
Edge material thickness (roll): 0.3 - 3.0 mm
Max. cross-section: for PVC 135 mm², for veneer 100 mm²
Roll diameter: max 830 mm
Pneumatic connection: 7-8 bar
Joint milling unit (milling cutters not included) for milling the working edge before the gluing part.
Workpiece preheating for heating the edge before glue application
Gluing unit 2158
Melting unit with granulate container
Electronic temperature control with LED
Magazine for solid moulding
Fixed lengths and roll moulding Infeed of fixed lengths with vacuum suction cup
Shears for roll material
Pressure zone C
Cutting unit HL 83 phase and straight cutting for cutting moulding overhangs at the front and back
3209 Pre-milling unit 1.5 kW
Height adjustment with overpressure. The motors work in co-fed mode
3220 Multi-milling unit For bevelling of different edges up to max. 3 mm thickness and radius milling R=2 and R=3 with a combination tool
3216 Fine milling unit (2x)
3503 Form milling unit FF12 below/above 0.4 kW (milling cutters not included) for rounding of postforming parts and rounding of corners in crossfeeding of both
4508 Multi-sickling unit MN 21 automatic For max. 3 different profiles
Copying above below and on the side for bevel or radius beading of pre-profiled PVC edgings 4506 Finishing unit FA 11 top / bottom
For processing edge along over / under consisting of: Beading unit glue joint for glue removal 6275 Electronic height adjustment
Hand pulpet for setting work LIGMATECH return conveyor ZHR 05/L/095 Optimum use: The return conveyor enables one-man operation of single-sided edgebanders
Remote operation from the infeed of the edgebander
Workpiece parameters: Length max. 2 500 mm, Length min. 300 mm, Width max 800 mm, Width min. 60 mm (at 40 mm workpiece overhang)
Thickness max. 60 mm
Thickness min. 8 mm
Weight max. 50 kg